I've done bout any board out there ;but,a hyperdyne sound board.I've got a brand new board coming;but,I don't know much about the wiring on this;due,to I want to use just one led set-up.My question is there anyone here whos anything about this board?Do you have a wiring diagram I can see?Where do get your sounds?What kind of sd card do you buy to use on this board?If you got the info please lay it on me ;so,I can learn!!Please!!
I have experimented with a single LED (or in this case a multi-die LED) running off of a SaberSD in the past, in order to get a flash occurring upon a clash to work and did make a wiring diagram for it...
cannibal869 of the FX-Sabers forum also came up with one that uses a single LED driver board and a Plector Labs Power Xtender. Here's his diagram...
My method requires a DPDT latching switch and has the "flash occurring upon a clash" dies attached to the vibration motor pads. This requires special parameters in the config file regarding the vibration motor settings.
cannibal869's method will work without a driver board but without that driver board, you would also need a DPDT latching switch. His method is probably a lot better than mine but I have not tested his method yet.
My second post in that thread is the one relevant to my diagram above.
You can easily adapt either diagram to work with a single die LED. On my diagram you would remove the DPDT 5V relay completely (and yes I know it only needs to be an SPST 5V relay) and on cannibal869's diagram, you would remove the Power Xtender. Of course the extra wiring for the extra LED dies would also need to be removed.
Regardless of diagram used, when using a multi-LED with a flash occurring upon a clash type of setup, activating the deflection switch will NOT activate the "flash occurring upon a clash" LED dies. it will only activate the blaster deflection/blade lock up sounds (whichever you have in place). I hope that helps.
jaltrooper: Hey guys! Dumb question...but are there any t-shirts available, or any other swag I can buy to support the Page?
Sept 23, 2017 8:52:58 GMT -5
ARKM: We have challenge coins. Contact Luke Skywalker if you want one.
Sept 23, 2017 13:50:47 GMT -5
Luke Skywalker: We never did any swag. There's never enough interest to even break even. My sponsor coin run was a huge success and helped us pay the bills well into 2018 and even gave us the money to fund a couple of one time costs we incurred this year.
Sept 23, 2017 16:23:33 GMT -5
Luke Skywalker: As for shirts. I really need to get one for me as well. I've been wanting one with our new logo since we changed over. My desire has always been that this is a site for the members. I consider you all my friends and have no desire to make a profit from
Sept 23, 2017 16:24:51 GMT -5
ARKM: Luke Skywalker, hit me up if you want the image I used for the front of my shirt.
Sept 23, 2017 16:25:38 GMT -5
Luke Skywalker: Site. I never intend to charge selling fees. The coin drive was a much better way to go imho. As for our logo, name and copywriter and TM's go. I have no issue with anyone wanting to use them. I ask two things. Please let me know prior. If it's crude
Sept 23, 2017 16:26:24 GMT -5
Luke Skywalker: and vulgar and casts us in a bad light I simply won't approve it. The other thing I think would be nice is that if our name is used on things like t-shirts that you do make a small donation to help support the site.
Sept 23, 2017 16:27:29 GMT -5
Luke Skywalker: My recommendation, and the place I will definitely go when I want to have a shirt done is TRA member defcon. Al's work is outstanding. Al is the Solo's Hold of saber bags and other fabric items. I've had him make me a couple of shirts and several
Sept 23, 2017 16:29:06 GMT -5
Luke Skywalker: saber bags. His merchandise is perfection.
Sept 23, 2017 16:29:32 GMT -5
Luke Skywalker: I think I'm down to about 8 coins.
Sept 23, 2017 16:30:26 GMT -5
Luke Skywalker: ARKM what image did you use? Was it the one with SVD's glowing eyes? I'm really curious to see how our logo looks on a shirt. Defcon would certainly need to use the flattened simpler version. For a detailed logo I think you'd need it silk screened.
Sept 23, 2017 16:32:23 GMT -5